Yamaha YZF-R125 Owners Manual: Tires

To maximize the performance, durability, and safe operation of your motorcycle, note the following points regarding the specified tires.

Tire air pressure

The tire air pressure should be checked and, if necessary, adjusted before each ride.

WARNING
Operation of this vehicle with improper tire pressure may cause severe injury or death from loss of control.

  • The tire air pressure must be checked and adjusted on cold tires (i.e., when the temperature of the tires equals the ambient temperature).

  • The tire air pressure must be adjusted in accordance with the riding speed and with the total weight of rider, passenger, cargo, and accessories approved for this model.

Tire air pressure (measured on cold tires):

0-90 kg (0-198 lb):

Front:

175 kPa (1.75 kgf/cm², 25 psi)

Rear:

200 kPa (2.00 kgf/cm², 29 psi)

90-185 kg (198-408 lb):

Front:

175 kPa (1.75 kgf/cm², 25 psi)

Rear:

225 kPa (2.25 kgf/cm², 33 psi)

Maximum load*:

185 kg (408 lb)

* Total weight of rider, passenger, cargo and accessories

WARNING
Never overload your vehicle. Operation of an overloaded vehicle could cause an accident.

Tire inspection


  1. Tire sidewall
  2. Tire tread depth

The tires must be checked before each ride. If the center tread depth reaches the specified limit, if the tire has a nail or glass fragments in it, or if the sidewall is cracked, have a Yamaha dealer replace the tire immediately.

Minimum tire tread depth (front and rear):

1.6 mm (0.06 in)

TIP
The tire tread depth limits may differ from country to country. Always comply with the local regulations.

WARNING


  • Have a Yamaha dealer replace excessively worn tires. Besides being illegal, operating the vehicle with excessively worn tires decreases riding stability and can lead to loss of control.

  • The replacement of all wheel and brake related parts, including the tires, should be left to a Yamaha dealer, who has the necessary professional knowledge and experience.

Tire information


  1. Tire air valve
  2. Tire air valve core
  3. Tire air valve cap with seal

This motorcycle is equipped with cast wheels and tubeless tires with valves.

WARNING


  • The front and rear tires should be of the same make and design, otherwise the handling characteristics of the motorcycle may be different, which could lead to an accident.

  • Always make sure that the valve caps are securely installed to prevent air pressure leakage.

  • Use only the tire valves and valve cores listed below to avoid tire deflation during a ride.

After extensive tests, only the tires listed below have been approved for this model by Yamaha Motor Co., Ltd.

Front tire:

Size:

100/80-17 M/C 52H

Manufacturer/model:

PIRELLI/SPORT DEMON MICHELIN/PILOT SPORTY

Tire air valve:

TR412

Valve core:

V3002 (original)

Rear tire:

Size:

130/70-17 M/C 62H

Manufacturer/model:

PIRELLI/SPORT DEMON MICHELIN/PILOT SPORTY

Tire air valve:

TR412

Valve core:

V3002 (original)

WARNING
This motorcycle is fitted with superhigh- speed tires. Note the following points in order to make the most efficient use of these tires.

  • Use only the specified replacement tires. Other tires may run the danger of bursting at super high speeds.

  • Brand-new tires can have a relatively poor grip on certain road surfaces until they have been "broken in". Therefore, it is advisable before doing any highspeed riding to ride conservatively for approximately 100 km (60 mi) after installing a new tire.

  • The tires must be warmed up before a high-speed run.

  • Always adjust the tire air pressure according to the operating conditions.

    Valve clearance
    The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a Yamaha dealer at t ...

    Cast wheels
    To maximize the performance, durability, and safe operation of your vehicle, note the following points regarding the specified wheels. The wheel rims should be checked for cracks, bends o ...

    Other materials:

    Checking the valves and valve guides
    The following procedure applies to all of the valves and valve guides. 1. Measure: Valve-stem-to-valve-guide clearance Out of specification Replace the valve guide. Valve-stem-to-valve-guide clearance = Valve guide inside diameter "a" - Valve stem diameter "b" 2. Replace: ...

    Installing the fuel hose
    1. Install: Fuel hose Fuel hose connector cover CAUTION:When installing the fuel hose, make sure that it is securely connected, and that the fuel hose connector cover is in the correct position, otherwise the fuel hose will not be properly installed. NOTE: W ...

    Introduction
    WARNINGDisc brake components rarely require disassembly. Therefore, always follow these preventive measures: Never disassemble brake components unless absolutely necessary. If any connection on the hydraulic brake system is disconnected, the entire brake sy ...

    2024 Copyright www.yam-r125.net |