Yamaha YZF-R125 Owners Manual: Multi-function display


Multi-function display

  1. Multi-function display
  2. "RESET/SELECT" button

WARNING
Be sure to stop the vehicle before making any setting changes to the multi-function display. Changing settings while riding can distract the operator and increase the risk of an accident.

The multi-function display is equipped with the following:

  • a speedometer (which shows the riding speed)
  • an odometer (which shows the total distance traveled)
  • two tripmeters (which show the distance traveled since they were last set to zero)
  • a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on)
  • a fuel meter

TIP

  • Be sure to turn the key to "ON" before using the "RESET/ SELECT" button.

  • For the U.K. only: To switch the speedometer and odometer/tripmeter displays between kilometers and miles, press the "RESET/SELECT" button for at least eight seconds.

Odometer and tripmeter modes

A brief push (less than one second) on the "RESET/SELECT" button switches the display between the odometer mode "ODO" and the tripmeter modes "TRIP 1" and "TRIP 2" in the following order:

ODO → TRIP 1 → TRIP 2 → ODO

When approximately 1.6 L (0.42 US gal, 0.35 Imp.gal) of fuel remains in the fuel tank, the odometer display will automatically change to the fuel reserve tripmeter mode "F-TRIP" and start counting the distance traveled from that point, and the last segment of the fuel meter will start flashing. In that case, pushing the "RESET/SELECT" button switches the display between the various tripmeter and odometer modes in the following order:

F-TRIP → TRIP 1 → TRIP 2 → ODO → F-TRIP

To reset a tripmeter, select it by pushing the "RESET/SELECT" button briefly (less than one second), and then push the button again for at least three seconds while the selected tripmeter is flashing. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically and the display will return to the prior mode after refueling and traveling 5 km (3 mi).

Fuel meter


Fuel meter

  1. Fuel meter

The fuel meter indicates the amount of fuel in the fuel tank. The display segments of the fuel meter disappear towards "E" (Empty) as the fuel level decreases. When the last fuel meter segment starts flashing, refuel as soon as possible.

    Tachometer
    Tachometer Tachometer Tachometer red zone The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. When the key is turned to "ON ...

    Handlebar switches
    Left Left 1. Pass switch "PASS" 2. Dimmer switch "/" 3. Turn signal switch "/" 4. Horn switch"" Right Right Engine stop switch "/" Start switch"" Pass switch "PASS" Press t ...

    Other materials:

    Shifting
    Shifting Shift pedal Neutral position Shifting gears lets you control the amount of engine power available for starting off, accelerating, climbing hills, etc. The gear positions are shown in the illustration. TIP To shift the transmission into the neutral position, press the ...

    Installing the swingarm
    1. Lubricate: Bearings Spacers Dust covers Pivot shaft 2. Install: Bearings "1" 2. Swingarm A. Left side B. Right side 3. Install: Swingarm adjusting collar "1" Swingarm "2" Pivot shaft Pivot shaft nut "3" a. Install, and then fully turn in the swingarm adju ...

    Installing the generator
    1. Install: Woodruff key Generator rotor Washer Generator rotor nut NOTE: Clean the tapered portion of the crankshaft and the generator rotor hub. When installing the generator rotor, make sure the woodruff key is properly sealed in the keyway of the crankshaft. 2. Tighte ...

    2024 Copyright www.yam-r125.net |